The Ultimate Guide to Finding Quality Used Hyundai Excavator Parts

1.The climate is cold in winter, the ambient temperature is low, the viscosity of the engine oil increases, and the friction resistance of each moving part increases, which reduces the starting speed and makes it difficult to start.

2.The battery capacity decreases as the temperature drops, which further reduces the starting speed.

3.Due to the reduction in starting speed, the leakage of compressed air increases, and the heat dissipation of the cylinder wall increases, which greatly reduces the temperature and pressure of the air at the end of compression, and increases the delay period of diesel ignition. In severe cases, it may even fail to burn.

4.The viscosity of diesel at low temperatures increases, which reduces the injection speed. In addition, the swirl speed, temperature and pressure of the air at the end of compression are relatively low, which makes the atomization quality of the diesel injected into the cylinder poor, making it difficult to quickly form a good combustible gas with the air and ignite and burn in time, or even fail to ignite, resulting in difficulty in starting.

When the engine replaces new piston rings, pistons or cylinder liners, due to the initial poor running-in, it is easy for the engine oil to enter the combustion chamber and burn, producing blue smoke. This phenomenon can generally be gradually eliminated after running for 8-10 hours.

(1) The oil level in the oil pan is too high.

(2) The engine oil in the air filter leaks into the combustion chamber from the intake pipe and burns.

(3) The piston ring is bonded to the piston ring groove by carbon deposits, causing the engine oil to leak into the cylinder and burn.

(4) The piston ring is excessively worn, or when several piston rings are installed, the opening gap has been matched.

(5) The matching clearance between the piston and the cylinder liner is too large.

(6) The piston ring is not elastic enough.

8 reasons for the engine speed drop of the excavator, 6 solutions are here!

As the name suggests, engine speed drop means the failure of the engine speed drop during the operation of the excavator. There are two manifestations of speed drop, one is a slight speed drop within 200 revolutions, and the other is a serious speed drop above 300 revolutions, which is likely to cause the excavator to suddenly shut down. There are 8 main reasons for the engine speed drop of the excavator.

1. The diesel oil circuit of the excavator is faulty. Generally speaking, when the diesel oil circuit is blocked, it may cause the speed drop phenomenon.

2. The hydraulic system of the excavator has a fault, so that the hydraulic pump cannot change the displacement normally, causing the system pressure to be too high, and the speed drop may also cause a machine failure.

3. The output power of the excavator engine itself is insufficient, the output power is lower than the rated power, and the speed is too low. There is also a problem with the main pump.

4. The engine uses fuel of poor quality or the water content of the fuel is too high, which will lead to insufficient engine power and speed drop.

5. When the air intake system leaks or is blocked, the engine will be short of air supply, resulting in incomplete combustion of fuel, and there will be speed drop and black smoke failure.

6. Due to the large gap of the solenoid valve, the fuel supply is insufficient, which causes the engine to drop.

7. The joint of the fuel supply circuit of the fuel system is loose or the pipeline is broken, causing fuel leakage or foreign matter blockage, resulting in insufficient fuel supply. In addition to speed drop, it may also cause flameout.

8. There are many reasons for speed drop, such as incorrect valve clearance, wrong injection timing, damaged turbocharger, faulty brakes, etc.

Having said so many reasons for the speed drop of the excavator engine, what should we do when the speed drop occurs?
The solutions are all here!

1. First, check whether the diesel used in the excavator is deteriorated, whether there are impurities in the oil, and whether the oil circuit is blocked.

2. Check the valve clearance of the excavator engine and the speed of the engine.

3. Check the intake pipeline, clean the air pre-filter and air filter element, and start the engine again.

4. Check whether the speed drop of the excavator occurs when the engine is under load?

5. Carefully check the engine to see if the engine failure causes the speed drop of the excavator engine.

6. In addition, the electronic control, hydraulic system, fuel system, etc. need to be checked.

To diagnose a faulty fuel injector, listen for any unusual engine noises or misfires. Perform a balance test to identify which injector is causing the problem. Use a diagnostic tool to check for fault codes related to the fuel system. If necessary, remove and inspect the injector for signs of clogging or damage, and replace it if needed.

After the machine has cooled down, locate the filters that need to be replaced (such as oil, fuel, and air filters). Use tools to remove the old filters, clean the installation area, install the new filters, and ensure they are sealed properly.